All posts by admin

How to Repair a Hot Tub

When You Need Help Fixing Your Hot Tub
Troubleshooting your hot tub issues will help you to understand the issues associated with most home hot tubs, along with the suitable measures to take in order to repair the problems. There are 3 locations which are frequently associated with hot tub problems and difficulties: repairing your filter, troubleshooting your heating unit and repairing your water. These 3 hot tub parts are accountable for a large majority of problems connected with home hot tubs.
Marketer Links for How to Repair a Hot Tub
[exactly what’s this?] Troubleshooting Your Filter
Problem # 1: Short amount of time in between filter replacements.
Possible Causes:
• Improper cleansing of filter on a routine basis.
• Water not well balanced correctly as an outcome of incorrect chemical application.
• Improperly sized filter system.
• Always wash filters completely and thoroughly, on a routine basis.
• Test chemical levels on a routine basis to ensure water remains well balanced.
• If the filter is too small for the water volume, increase the filter size.
Issue # 2: Water leakage around filter.
Possible Causes:
• Damaged or worn out o-rings, tank or loose plumbing.
• Determine the area of the issue (whether it is coming from the o-rings, tank or pumps).
• If the tank is leaking, change it immediately.
Fixing Your Water
Issue # 1: Dirty and cloudy water.
Possible Causes:
• Dirty filter
• High pH and alkalinity
• High Calcium
• High Bacteria.
• Clean the filter completely or have it entirely replaced.
• Drain the water entirely and refill the spa.
• Test all chemicals in your hot tub.
Problem # 2: Green water.
Possible Causes:
• Algae growth
• Shock sanitizer
Issue # 3: Foamy water.
Possible Causes:
• Soft water
• High TDS (total dissolved solid) levels
• High pollutant level.
• Test and include liquid calcium.
• Completely drain and refill the tub.
Repairing Your Heater
Issue # 1: Hot tub water isn’t heating.
Possible Causes:
Thermostat might be accidentally denied.
• Not enough insulation.
• Check the thermostat to make sure it is at the proper level.
• Increase the quantity of insulation if required.
Issue # 2: Heater cycling on and off constantly.
Possible Causes:
• Dirty filter
• Low water level.
• Clean filter cartridge or totally change hot tub filter.
• Raise the water level if it is currently too low.
Issue # 3: Takes too long to heat up the hot tub.
Possible Causes:
• Dirty filter.
• Daily filtering and heating cycle not running long enough.
• Damaged or ineffective insulation cover.
• Improperly working thermostat.
• Clean or replace filter cartridge.
• Reset the time clock if it is not running enough time throughout the day.
• Repair or replace your present insulation cover.
• Repair or replace thermostat if it is not working effectively.

Always cover the tub when you’re not using it, and check to be sure the cover is properly secured on the hot tub, because in this way you can avoid wasting energy which is good for you as well as for your pocket.

All Hot Tub Covers use Sunbrella marine fabric which is rated by YEARS outdoors. In fact Sunbrella fabric will still look brand new after ten years outdoors. Nothing else comes close. 

Infused Spa Waters to Drink in the Hot Tub

When we typically mention spa water, we are discussing the water in a tub. Today however, we take a look at Spa Water from another point of view. it’s typical for resort spas to use naturally flavored water to their guests– some individuals call it ‘spa water’.
Hot Tubs and Spas are great for ridding the body of contaminants, cleaning the pores and skin. When you put excellent stuff within you while in the hot tub, you can increase the Detox effects with natural fruit coolers that are simple to make, therefore great for you!
The majority of these infused water dishes have 3 components, however in a pinch, 2 is OK. Get innovative! Raid the refrigerator for herbs, fruits and roots and the cabinet for spices and extracts.
Not to make complex things, however I am also a spa fragrance user, and obviously I have rather a choice, big bottles of my favorites, and lots of samples of various unique scents. The challenge is to attempt to match the essence of the cooler with the spa fragrance. I’ve made some recommendations below.

Healthy Hot Tub Coolers
If you are missing out on 1 or 2 or the components, it’s still tasty! Set this cleansing cooler with aromatherapy like the Elixirs Eucalyptus Mint, or the Crystals Cucumber-Melon spa aromatherapy.

One vanilla bean, or you can substitute a 1/2 teaspoon of vanilla extract (almond is excellent, too!). This cooler will unwind and relieve, and can be quickly matched with other Vanilla aromas or Paradise Floral spa aromatherapy aromas.

3. Citrus, Strawberry, Green Tea – [recipe]– Green tea has many health advantages, however you do not need to drink it warm! It’s the perfect base for citrus, using a blend of lemon, grapefruit and orange, to your taste. The strawberries and honey include a touch of sweetness, while the mint adds a little interest ~ you can match this infused water drink with aromatherapy spa scents like Peony Green Tea Elixir, or the Jasmine spa crystals.

4. Strawberry, Kiwi, Mint– Strawberries regulate sugar level, help in digestion and immune system and cardiovascular health. Kiwi adds a natural tartness that’s a best enhance to the dull sweet taste of the berry. Mint speeds up metabolism and soothes. Take a huge swig of this in the tub and I always feel calm, yet alert. To match the tastes of this healthy infused water, attempt our Eucalyptus Mint or Kiwi Pear elixirs to add another dimension of relaxation. Spa Water– it’s not just something on the
exterior of your body– add fruit instilled water to your spa routine, and you’ll come out sensation terrific! It’s constantly motivated to consume great deals of fluids while you’re in a hot tub, infuse some fruit to your water for revitalizing detox therapy. I try to drink 24 ounces throughout a 30 minute spa session. It’s become part of my essential equipment, prior to I head out to the spa.

We want everyone to get the maximum benefit from their hot tub which is one of the reasons we recommend the lightweight hot tub covers from

Heavy Hot Tub Covers can be more than annoying they can be a serious hazard. The covers from don’t use rigid foam panels like typical hot tub covers. Instead they use air to insulate which aside from being more efficient, the air chambers don’t suck up moisture and stay easy to use.

Why not visit and order a new hot tub cover for your spa today and save yourself the aggravation of wrestling a heavy cover?


The best ways to Install a Portable Spa

You saw our terrific costs on brand-new hot tubs, and unless this brand-new spa is a replacement spa, you’re questioning exactly what’s included in spa or hot tub setup.
Whether you set up among our Plug & Play 120V spas, or a complete highlighted premium spa working on 4-wire 240V, requiring an electrical expert, you’ll have to plan a couple of things in advance of getting your brand-new spa.
spa Fencing
There are 2 types of fencing needed, security fencing, to keep individuals and animals out, and privy fencing to keep out spying eyes.
For safety fencing– in the majority of localities, a spa is under the exact same or comparable fencing guidelines as use to pool, in the interest of public security. Usually, a spa within a fenced-in yard is acceptable. There might not be an examination of the fence in some cases, however still required however.
Privy fencing supplies privacy, also a factor to consider when setting up a hot tub, as well as blocks the wind, which can cool the spa, and provide you a chill while soaking. Frame your spa with big plants, and a 2 sided lattice fencing, or a pergola or cabana set up around the tub. Outside roll-up shades are also popular.

hot tub Location
A hassle-free location is best, near the door. The location should be clean and dry (never ever muddy), and close to power and water. Guard the spa from as much sun, wind and rain as you can, and make sure that storm waters will constantly drain pipes away from the spa.
The surface area supporting the spa should be solid, when full with water, a 6 person hot tub can weigh near two loads! No wooden decks and definitely no verandas. A level, 4 inch slab of steel mesh enhanced concrete, on top of 4 ″ of gravel suffices in a lot of cases.
Many hot tubs can be sunk into a deck when appropriate load bearing assistance is constructed to hold 150 lbs per square foot. Lastly, think about view– both the view of the spa from your house and the view that you’ll have while in the spa.

Moving a Spa
When the tub is provided to your house, it won’t go any even more than the driveway. From that point on, you have to determine the quickest and best route to the spa placement location. Expert spa movers use a Spa Kart to carry spas across yards, over steps or into tight places within the house. Inspect for regional spa movers or rental buy a service, some even lease Spa Karts. Over smooth concrete it’s easy, but when the surface area gets rough and irregular, you’ll require something with big tires, to support a spa of 400-600 pounds, in addition to straps and a number of hands to assist.

Hot Tub Wiring
120V Spas: Most rotomold spas are plug and play; 120V spas that plug into a basic, devoted outlet. Dedicated implies that nothing else is running on that circuit. Plug the GFCI cord into a weatherproof 120V outlet (not GFCI), on a 15 or 20 amp breaker. The outlet ought to be between 5 and 10 feet from the spa, and no extension cables. 120V spas utilize less volts due to the fact that they have smaller sized pumps and heaters, and couple of other features.
240V Spas: Larger hot tubs with 4-5 hp pumps and high wattage heaters need a 6 AWG, 4-wire 240V service to the spa, on a devoted 40-60 amp breaker, with a cut-off switch or sub-panel, and other requirements, according to regional electrical codes. They do not plug in like a washer or clothes dryer, however utilize 4 wires within PVC channel, with the last few feet of versatile channel bring the wires straight in through the cabinet and connecting to the spa pack.
Wiring a spa with 240V is not a suggested DIY job. A license and an assessment is required in most locations, so it’s best to get in touch with a regional electrical contractor who recognizes with the procedure of wiring spas and jacuzzis. In many cases, hard-wiring a spa to the home main breaker, and setting up a power cut-off near the spa is a $500-$ 900 job, depending on the length of the run from the breaker panel to the spa, and the path it should take a trip.

Filling a Spa
When the wiring and evaluations are done, you can fill the spa, insert the spa filter cartridge.
When you initially fill an empty spa, and in some cases when you drain and refill the spa later, and air lock will take place in the pump, and prevent the pump from catching prime. Instead of running the pump without water, which can damage the seals, loosen the union nut in front of, or on top of the spa pump simply enough to let the air escape, and enable the water to fill the pump.

Enjoying your New Spa
That’s the very best part, after all the working of picking, ordering, getting, moving, electrical wiring, examining, filling … now you finally get to take pleasure in the fruits of all your difficult work and money.

When you’re ready to cover your investment, visit SpaCapcom. While spa manufacturers have been working on designing and building better spas, has been building the perfect spa covers.

No matter which company you purchase your spa from they will offer a traditional rigid foam filled spa cover. And just like every other foam filled cover ever made, those panels will eventually begin to saturate with moisture from the steam coming off the spa water, until they are too heavy to lift.

Bar lifters won’t help once the cover becomes too heavy either because you will still have to flop it over the bar while trying not to strain yourself. Then push it off the end of the spa. When the cover is heavy it will either rip itself apart (because the seam of the cover is not built to handle the added weight) or worse it will rip the bar lifter off the sides of your spa potentially causing damage to the spa cabinet.

The SpaCap Spa Covers by contrast, don’t employ foam so there is nothing to soak up the moisture. They are built to stay lightweight and easy to use. Visit and order one for your swim spa today.

Show up the heat, and enjoy your brand-new spa

Dealing with Arthritis in a Swim Spa

Assist for Rheumatoid joint swelling Sufferers in Hot Tubs and Swim Spas.

On the off chance that you’ve ever come across the torment of osteoarthritis or have needed to enjoy someone you understand and like sustain with it, you will be satisfied to understand the Osteoarthritis Foundation to a fantastic degree recommends the recovering properties of hot tubs or perhaps the hot tub in your Swim Spa. Individuals with osteo-joint swelling have an incredibly troublesome time moving and by getting submerged in warm water, they’re alleviated of a portion of the discomfort and are even in a position to get the some possible relief.

As reliably, with any brand-new action, on the off possibility that you are an osteo-joint inflammation sufferer and would want to start valuing the Swim Spa, please first evaluate having a medical professional prior to you begin, but inform him that you can set the spa temperature between 80 degrees all the way as much as 104 degrees … so f need be, put it at a temperature level of listed below body temperature, say 90 degrees.

At the point when you choose to start any motion in your Swim Spa, its a great idea to loosen up first … do interior water stretches. Begin by permitting your body to become reasonable with the warmth for a few minutes prior to starting any exercises. Its been stated that because of the smooth warm currents that there can be remedy for arthritis discomfort.

It’s remarkably necessary to think about focuses gradually when practicing in a warm tub for a few factors; one is simply in light of that you can strain muscle lots on the off opportunity that you aren’t efficiently warmed up before starting, 2 is the way that it is imaginable to more than aim in the Swim Spa by performing a great deal of or doing it for excessively protracted to anywhere you get to be woozy and unsteady. Getting to that point will not aid any doing activities, and it can be negative to your basic well being. The third cause to consider takes place after you’ve exercised, keep up as a primary top priority that now that the muscle events are as of now extended and fulfilled expectations, it is crucial to keep them warm for a long period of time before escaping from the Swim Spa to enable your muscles to relax in the past hitting the cooler air.

For that person who withstands with osteo-joint inflammation, the crucial reality that they’re ready to move with less misery in a warm tub or perhaps a swimming pool is nothing short of terrific. Those with joint inflammation are in stable agony and a critical of it needs to made with the straightforward reality that there is a gravitational draw towards the earth we live on and that is extremely reduced in the event that they are immersed in water. Open to warm water is an extra advantage on the grounds that it will likewise activate the veins to expand, that will think about a lot more blood and oxygen to stream to muscles and skin to not state the heart.

Okay, as you would expect, we need to point out that if you indicate to obtain the healthy benefits from using your Swim Spa, you have to be able to use it easily daily. That needs that it be basic, or we will begin to discover elements not to. After remaining in the Spa Cover service for thirty plus years, the folks at have learned a few aspects of human nature when it pertains to using a hot tub.

When we at first get our swim spas, we are thrilled and it is easy to find the time to use it daily. Like a kid with a new toy. Eventually, that “newness” diminishes. Then you need to choose that the benefits you receive from using the swim spa deserve the time it secures of your schedule.

The standard foam filled Swim Spa Covers offered at every spa dealer throughout the country is the issue. The cover that gets included when you buy the spa.

The foam starts to fill with moisture from the steam increasing off the swim spa water. After a couple of months, the Swim Spa Cover is heavier however since you have been using the spa everyday you didn’t notice it.

Before you know it, getting the cover on and off takes a lot more effort. You might not even purposely discover it however one day you consider getting in the tub and you decide to avoid it. You’re simply not up to it this evening.

That easy foam filled cover ends up being a barrier between you and the swim spa you invested all that cash in.

Prior to going out and purchasing another Swim Spa Cover just like the one you’re changing, think of something much better.

At, they have actually been constructing Swim Spa Covers, that are lightweight, simple to use and constructed to remain that approach. There are no stiff foam panels in the SpaCap so there’s definitely nothing to soak up that steam and get heavy.

Swim Spas & Weight-loss

In America today, becoming overweight seems to be a way of life anymore. All the junk foods consumed by us, places on the pounds. Exactly what’s good is getting in your Swim Spa and putting yourself through a great workout that in turn, helps you loose the weight while strengthening your muscles. Looking your finest is among the advantages you can receive from swimming several times a week with your swim spa.

Think of how nice it would be to get in the warm soothing water in the morning, going to work, and after that again during the night, working off the pounds and relieving those day-to-day stress … Ah. that warm pulsating water works marvels. And not to mention how it may help you sleep like an infant!

There are many excellent workouts that you can doing it your swim spa. Not just, swimming versus a regulated river stream existing, back pedaling against the river like flow, or running in place against an existing. You can also, have a rowing device effect, a tether line set up, while doing numerous extending workouts, and a lot more ways to loose weight and helping you keep fit. Swim Spas are simply Awesome for helping you remain fit.

Obviously the Swim Spa shows that the hot tub isn’t really just for relaxing any longer. It’s no secret that physical activity burns calories so the technique is to be active even in the spa.

Extending and rotating your limbs is easier to do in the swim spa due to the fact that the water assists support you and warms your muscles while you work them. It’s likewise deeper than a common hot tub so you can have more variety of movement. Start gradually with some stretches and arm movements with your arms and shoulders under the water to obtain limbered up. Then sit up straight and do some twists (carefully) turning the your shoulders to the left and right while keeping your knees and hips fixed.

Use Yoga

When performed safely, yoga is among the easiest workouts for those who love hot tubs. With assistance from a yoga instructor or spotter, try postures such as the “wall pet”, “up pet,” or “lunge twist.” These postures stretch a number of muscle groups at the same time, consisting of the arms, legs, torso, and back.

The breathing that hot tub yoga requires likewise assists the body relax and aids digestion. If you engage in hot tub yoga after consuming, the deep breaths will help move the food through the digestive system more effectively than it would if you were simply sitting on the couch. Deep breathing likewise increases metabolic process so it not only burns calories it also helps your body recuperate quicker from sickness and or injury.

With that in mind, as you practice your hot tub yoga, aim to be conscious of deep controlled breathing. Get that oxygen into your blood and moving through your body.

Play Games

As I said above, hot tubs are not just for relaxing. They’re also enjoyable locations to play active video games with your family and friends. Try Hot Tub Hockey, in which groups make points by moving an item like a rubber duck or Ping-Pong ball to each other’s sides of the tub without using their hands. You can also attempt Pass the Bottle, needing everybody to pass a securely capped bottle of water around the hot tub using every body part other than their hands. Gamers may not use the same body parts twice in a row (i.e., passing from knee to knee or shoulder to shoulder). If the bottle drops, the dropper must carry out a penalty task and the game begins again.

Okay, as you would expect, we need to discuss that if you mean to get the healthy gain from using your Swim Spa, you have to have the ability to use it quickly everyday. That requires that it be easy, or we will start to discover factors not to. After remaining in the Spa Cover organisation for thirty plus years, the people at have actually found out a couple of aspects of humanity when it concerns using a hot tub.

When we initially get our swim spas, we are excited and it is simple to find the time to use it everyday. Like a kid with a new toy. But ultimately, that “newness” diminishes. Then you need to decide that the advantages you receive from using the hot tub are worth the time it takes out of your schedule.

You have to choose a time of day that it works for you and make it part of your regimen. Personally, I prefer to make it at the end of the day right before bed. It helps me sleep much better and get up revitalized. But that’s me. Some individuals enjoy to begin their day with a dip in the spa before the day gets hectic. They find it helps them keep a favorable outlook throughout the day.

It doesn’t matter when you decide it works for you, you just make it part of your regular and go from there.

However that’s not the problem. The important things that triggers most swim spa owners to ultimately stop using their spa is the Swim Spa Cover The standard foam filled Swim Spa Covers available at every spa dealer across the country. The cover that gets thrown in as an after thought when you buy the swim spa. Crazy right?

Here’s how it occurs. The foam starts to saturate with moisture from the steam rising off the spa water. It does not occur quick, in fact it happens gradually in time so that you don’t even see it. After a few months, the Swim Spa Cover is heavier but because you have actually been using the spa everyday you didn’t notice the gradual change.

Before you know it, getting the cover off and on takes a lot more effort. You might not even purposely notice it but one day you consider getting into the tub and you choose to skip it. You’re simply not up to it tonight.

Why would you “skip” the important things that makes you sleep better and live much healthier? Due to the fact that it needs excessive effort. That easy foam filled cover becomes a barrier in between you and the hot tub you spent all that cash on. The same swim spa you could not wait to get into, is just too much work now because of a heavy swim spa cover.

Eventually, you can’t keep in mind the last time you used it.

You then need to choose. Do you get a brand-new cover and get back to using it or do you (and this is the one that just makes no sense to me) get rid of it and recover that part of your back yard.

I hope you choose to get a brand-new cover. That hot tub is like an everyday getaway that your mind and body need to “re-boot” and stay healthy. But before heading out and purchasing another cover just like the one you’re replacing, think about something much better.

At, they have been constructing Swim Spa Covers, that are light weight, easy to use and built to stay that way. There are no rigid foam panels in the SpaCap so there’s absolutely nothing to absorb that steam and get heavy.

Installing Your Own Spa

Ways to set up a hot tub in your backyard

You don’t require to spend much time luxuriating in a hot-tub spa to discover its relaxation advantages. Backyard medspas are ideal for households on the go.
Spas are not for everybody, nevertheless. All those warm, rubbing bubbles can raise blood pressure and heart rates, while reducing blood sugar level. They’re not advised for babies, the extremely old or those with diabetes, hypertension or heart disease.
Choosing Your hot tub
Looking for hot tubs can be a little confusing. There are so numerous brand names and models, and every salesperson appears to highlight a various set of functions. As usual, price is an excellent sign of quality. Hot Tubs range in between $1500 and $10,000, with the much better designs beginning around $3500. These are 3- and four-person tubs. Larger health clubs cost more, and those with great deals of specialized jets, DC-powered pumps and ozone-generating water purifiers, can quickly reach $6000 to $8000. Add devices and you can easily pay a couple thousand more.
A few companies offer two-person hot tubs, but a lot of start with three- or four-person seating and go up to the eight-person size. A full-size tub can determine 8 x 8 ft. and 42 in. Huge tubs are great for big, active families with plenty of area, however smaller sized tubs are no less appealing or healing.
Filled with water, a full-size tub can weigh 5500 pounds – more than many conventionally framed floorings and decks can securely manage. If you cannot beef up the floor, you’ll either need a smaller sized tub or a setup on concrete.
The majority of spa shells these days are made in two layers: an enhanced fiberglass base and a formed acrylic shell laminated over it. The shell is piped and fitted with pumps and jets, and is insulated.
A lot of spas are wired with 240-volt electrical equipment and some include DC converters. DC motors run more silently and DC circuit boards are very trustworthy. A few economy tubs are readily available with 120-volt circuitry to make the electrical connections easier – you just plug these designs in. These tubs are small, their heating units are less effective and they shut down when the jets are turned on.
Business generally offer 10- to 20-year service warranties against leaks through the shell, however these types of leaks are unlikely given the thickness of the laminations. More probable are surface problems such as blisters, cracks and staining. Look for a 5- to seven-year surface service warranty and three- to five-year defense on the pumps.
The spa we selected is a JacuzziTriton – a large design with all the bells and whistles. Powered by two 4-hp DC pumps, it sports 42 jets – 10 totally adjustable and 16 directional, 10 air injector jets and a set of lounge jets that offer complete back massage. Other features include a push-button control for the tub operation, an AM/FM/CD gamer, underwater lighting, 4 headrest cushions and dual waterfall components. Most importantly, it includes an integrated ozone generator and a water cleanser that conserves money and time by decreasing the quantity of chemicals needed. At 42 x 91 x 91 in., it’s not the biggest tub, however it comes close. Jacuzzi’s Triton has a sticker label price of $10,000, but normally sells for less.
Locating The Tub
To fit the tub, we cut away some of the bank and built a little retaining wall. When choosing where to place your unit, keep in mind that hot tubs need service access on all sides.
We prepared for one side of our tub to be 18 in. from our deck, then distributed the width of the tub plus an extra 18 in. to establish the face of the brand-new retaining wall. To accommodate the depth of the retaining-wall blocks, plus a foot for drain gravel, we cut into the bank an additional 24 in.
To construct the keeping wall, first dig out the bank. Using some of the removed soil, grade the setup location just enough to enable drainage far from the tub. For the very first row of landscape blocks, excavate a trench about 4 in. deep and fill it with pea gravel or crushed rock.
Level the gravel and compact it with a hand tamper or gas-powered sand-plate tamper. String a level line to guide the very first row of blocks. Utilize a 4-ft. level to make sure the course is level.
Set landscape blocks on pea gravel in the trench to match the leveled string. Then, examine this very first course with a 4-ft. level.
With the first course in place, set the staying blocks. The type of block we utilized has a lip along the back edge that locks over the block listed below. When turning a corner, you’ll have to break off this edge to maintain the very same obstacle between the courses. To keep these blocks from moving forward gradually, glue them in place with masonry building and construction adhesive. When you finish the wall, back-fill with gravel. Cover the top of the gravel with weed-guard material and soil.
Where the wall turns, break off edge-lock tabs on the blocks. Next, use building adhesive to hold the blocks in place.
Next, set the type lumber for the concrete pad, and level it in all directions. Fill the kind with concrete and screed it with a straight 2 x 4.
While a sufficient pad might consist of 2500-psi concrete, boosted with iron rebar or wire mesh, regional electrical codes would have needed us to ground this enhancing metal back to the electrical service panel. To avoid this problem, we upgraded to 3000-psi concrete and added fiberglass reinforcement to our 4-in.- thick pad.
After pouring concrete in a leveled form, screed it with a straight 2 x 4. Float and trowel the surface area smooth.

We moved our tub from the driveway to the website on a little trailer. Carefully move the tub off and position it on the slab.
Setting The Tub
If you buy your hot tub from a spa dealership, the company will typically set it in location for you. If you purchase through a house center or discount shop, however, you might need to move and set up the tub yourself. Presuming your tub is in a dog crate in the driveway, get rid of the packing and slide the tub onto the trailer.
Electrical Work
Water and electrical power don’t mix, so if you’re not comfy with your circuitry skills, this is a good time to employ an electrical expert.
In our case, regional codes required a constant bond wire from the tub to the service panel. We also required a detach box at least 5 ft. from the tub and a GFCI breaker protecting the entire circuit.
Due to the fact that of the DC converter, we utilized just 2 hot wires, a grounding wire and a bonding wire – no neutral was required. Our spa was close to 70 ft. from the circuit box, so we ran 6-ga. stranded wire for the 2 hots and the ground wire, and an 8-ga. bond wire. While all outdoor wiring needs to remain in conduit, we chose to set up the entire run from the main panel in 1-in. PVC pipeline.
Begin by running the channel from the circuit box to a home rim joist near the tub. Bore through the siding and the joist with a hole saw and feed the avenue through the joist.
Bring power from the main panel to the outside through the home’s rim joist. Bore a hole to move avenue through.
Glue a POUND conduit box to the avenue and extend the channel up to a disconnect box. At the tub, sign up with a POUND to the avenue with a slip coupling to permit the ground to shift seasonally without stressing the conduit connections. Here, we brought it up to the deck with another slip coupling and LB, and then ran it to the disconnect box.
At the tub, splice a slip coupling just listed below the LB connection. Run the conduit in a trench at least 18 in. deep
With the channel in location, pull the 4 wires from the primary panel to the disconnect box with a fish tape.
With conduit from the panel and tub conference at the detach box, use a fish tape to pull the 4 wires through.
Bind the hot wires to the hot terminals and the ground wires to the ground terminals. In our case, it was needed that the bonding wire continue undisturbed through the disconnect panel.
Inside the detach box, connect the hot wires to the four hot terminals, and the ground wires to the 2 ground terminals.
Complete the outside wiring by making the hot, ground and bond connections in the spa’s devices box. You’ll find the terminals clearly identified.
At the tub’s control box, secure the hot wires, the ground wire and the bonding wire inning accordance with producer’s directions.
Link the circuit hot wires to a 50-amp GFCI breaker in the service panel and connect the bond and grounding wires to the panel’s grounding bus. Leave the circuit’s power off up until after you’ve filled the tub with water and your work has actually passed examination.
In the circuit box, link the circuit with a 50-amp, 240-volt GFCI breaker. Turn off the power and prevent touching the panel.
Completing Up
To make steps for our hot tub, we first poured a 31-in.- broad concrete pad, and after that built 2 30-in.- wide step boxes from cedar. Make the box frames out of 2 x 6 lumber. Size the depth of the bottom box for two 2 x 12 treads, and the depth of the top box for one 2 x 12 tread. Put together packages with screws.
Construct frames from 2 x 6 cedar for the two steps. Develop the larger bottom frame first and connect two 2 x 12s to its top.
After the bottom box is developed, secure the top box frame to it with screws owned diagonally from the within
Location the smaller sized frame on the rear edge of the lower step and protect the two levels with screws owned diagonally.
Then, add the leading tread and stain the assembly to match the skirting.
Finish the step assembly by screwing a single 2 x 12 tread to the top box frame. Stain the actions to match the tub.

1. Make sure hot tub/spa is filled to proper amount. The Proper amount is whatever the spa manufacturer suggests the spa water to be for proper operation of the spa. Swim Spa Covers/ Hot Tub Covers rest right on the water surface so make sure your spa has water in it.

2. Distinguish the top from the bottom and observe the location of the valves. The top is the side of the Spacap with the Sunbrella fabric on it that shows when it is on the spa. The bottom is the side with the valves on it. When the SpaCap is on the spa, the bottom will rest on the water.

3. Place the SpaCap cover on spa, laying it on water surface. Top, Sunbrella side up. You are meant to fold the cover back to expose the valves to fill your SpaCap.
Note: Valves are meant to be on underside when your cover is on hot tub.

4. Inflation. Open the flap of the valve you intend to put air in. Prop open the inner check valve with a plastic funnel. The funnel will also divert the air into the cover. In order to put air into the SpaCap you need something that moves a volume of air. For example a shop vac that has an exhaust port you can hook the hose into or a leaf blower. An air compressor would work but it will take longer since it is designed to move air under pressure. The SpaCap is not designed to be under pressure.

Inflate the “Top” valve first until there is about eight inches of air. Inflate the bottom unmarked chamber to desired level. We recommend using a shop vac to inflate your Swim Spa Cover/ Hot Tub Cover.

5. Close valves and center the cover on the spa so that it evenly covers the entire hot tub.

6. Place fasteners as needed. The fasteners help the SpaCap keep its shape, insulate better and keep the moisture running off. The fasteners should be equally spaced and should go below the acrylic of the spa. If your spa has a wood lip that protrudes further then the acrylic the fasteners should go about three inches below the wood lip. If as you are installing the fasteners the cover becomes difficult to fasten on the last side, you have too much air in the cover. There should still be a little give in the cover when fastened and the corners should not be lifting.

If your water is not heated when you first fit the cover, do not inflate the cover all the way. When the water starts to heat up, the air in the cover will, too, possibly causing the cover to be over inflated.

Set up the polyester filters in the filter real estates and fill the tub with a garden hose.
With the setup complete, it’s time to fill the tub. Prior to filling, however, set up the polyester filters in their real estates.
Insert the tube into one of the filter housings and tape it in location. Anticipate the tub to fill in about 45 minutes.
Fill the tub through the filter real estates with a garden pipe. Tape the tube in place. The tub must complete about 45 minutes.

Preventing Freeze Damage to a Spa or Hot Tub

freeze damage is when water freezes and broadens within spa pipelines or spa equipment, like your filter, pump or heating system.
Water expands about 10% when it freezes. For pipelines or equipment that have a little quantity of water within, for example a pipe that is less than half filled with water, unused space inside the pipe enables some ice growth.
When pipes, pumps or filters are over half complete of water, there is little space for growth, and even extremely thick products can rupture from the ice pressure inside.
Today’s lesson centers on ways to avoid freeze damage in a spa or hot tub, which can be a complicated and pricey spa repair work, and sometimes, could ‘total’ the spa, with repair work expenses of thousands of dollars.
There are 3 ways to prevent freeze damage in a spa or hot tub
1. Winterize the Spa
We do not recommend that you winterize your spa, unless you are sure that it won’t be used for at least 3 months, or it can not be maintained (at a vacation house, for example).
Winterizing the spa is a procedure that takes a few hours, to drain all of the water from the spa, and utilize air to ‘blow the lines’, to require water from the pipelines, hoses and equipment.
We did a short article on How to Winterize a Spa, if you are considering winterizing the spa. It’s simple, however if you desire guarantees of a proper winterization, most spa service business offer this service.
2. Usage Freeze Protection
Modern medspas packs will have a freeze security mode on the spa that will turn on the flow pump when temperatures get near freezing. If you don’t see this available in your control alternatives for the spa, you may not have freeze security.
Freeze security works with an air temperature sensor that interacts with a controller, wired into the pump power circuit. Freeze security is standard equipment on all our Digital, Flex-Fit and Balboa spa loads, which is the most basic way of adding freeze security for older spas with air activated spa packs.
For aid including freeze security to your spa, feel complimentary to call our spa techs with some info about your spa.
3. Run the Pump
As long as water is moving through the pipes– all of the pipes, the water will not freeze. Open all of your jets, if your spa has the capability to separate banks of jets. Low speed can be used, as long as all pipelines are made use of.
The water need not be hot, or even heated at all–. As long as it’s moving through all the pipelines and equipment when temperatures are listed below 32 degrees. The heat from the spa pump, under a closed skirt, is also valuable to heat up the devices. Naturally, a spa cover need to be used during winter to avoid ice forming on the spa surface.
Throughout winter, it might be smart to operate your pump 24 hours daily in cold northern areas, or set the time clock to switch on the pump for 10 minutes every half hour.

• Adding heat to your spa, a hot spa can give 24 hours of security
• Keeping a tight fitting spa cover in place and protect
• Spa insulation– the more there is, the more protection you have
• Hang a 100 watt shop light, under the skirt, next to the spa pack

Always cover the tub when you’re not using it, and check to be sure the cover is properly secured on the hot tub, because in this way you can avoid wasting energy which is good for you as well as for your pocket. If you are using a traditional rigid foam cover to do this the dealer you bought it from may have recommended to clean and condition it once a month with vinyl protector, because in this way you will avoid to let UV rays to damage it. What they don’t tell you is that the vinyl on the outside of your cover is rated by HOURS outdoors. 1500hrs to be precise. Cleaning it and rubbing it with vinyl treatment is just wasting your time and money while prolonging the inevitable. Which is why Hot Tub Covers employ Sunbrella outdoor fabric which is rated by (wait for it) YEARS outdoors. In fact we have seen Sunbrella fabric still looking brand new after ten years outdoors. Nothing else comes close.  That said, if you do need to clean your cover for some reason, use the solution just on the top of the cover and pay attention to not let the solution to pour into the water of the spa. It is better to take it off and clean also the underside of it with a mild cleaning solution. Rinse well and air dry.

If you discover a spa or hot tub that is strong frozen, and perhaps you spot some freeze damage currently, the devices needs to be defrosted out. If there are broken pipelines, using electrical area heating systems might be unsafe, under the skirt.
If you have an outdoor camping tent large enough to place over the spa, you can thaw out a spa in a couple of hours. When I was servicing medspas in Colorado, we had a camping tent we utilized whenever we ‘d get a ‘frozen spa’ call. We utilized a little kerosene heater once the tent was established over the spa, and monitored it carefully. If there was freeze damage, (and there generally was), we would drain it entirely, make the repair and fill it back up.
Including warm water to the spa is another old trick. With a little adapter, a garden hose pipe can be connected to most sink faucets, to bring hot water to the spa, to raise the water temperature for a faster thaw. Sometimes, you can carefully wet frozen pipes with warm water– just do not spray any motors, electronic devices or controls.


If your power stops working throughout winter season, keep in mind that a heated spa with a good fitting spa cover has enough warmth to prevent freeze damage for 24 hours approximately, longer if it’s effectively insulated.
To maintain some heat under the spa skirt throughout a power failure, you might hang a 100 watt store light in an area close to the spa pack. In some scenarios, a small area heating unit might be safe to use likewise, inside the spa cabinet, in a dry place, till power is brought back.

Should I Buy a Used Hot Tub or a New Hot Tub?

Are you considering buying an utilized hot tub? Prior to you begin searching websites like Craigslist and eBay, you should discover why purchasing an utilized hot tub isn’t really the very best method to conserve cash. Purchasing a used hot tub will likely cost you more loan, time and tension in the long run.
Let’s take an appearance at 5 reasons that buying a brand-new hot tub is a much better choice than purchasing one used.
• You Know the Quality of Your Hot Tub Parts
When you purchase a used hot tub, you could be buying one with extremely low quality parts. Low quality parts imply that your hot tub will utilize more energy, have actually to be replaced more often and will not keep your water as tidy.
When you buy your hot tub new, you ought to know exactly what parts are used and how well they perform. You can either learn by speaking with a sales representative or looking up the information online.
ThermoSpas ® makers hot tubs utilizing just top-notch parts. From heating units with titanium components to our trademarked Throttle Control Valves, we employ the hardest quality standards on each of our parts. Every spa we make need to score 100 percent on an extensive checklist prior to passing inspection.
This implies you’re guaranteed to get a spa that will last.
• You Don’t Have to Worry About How Well-Maintained Your hot tub Was
No matter what the previous owner says, you do not understand how well they took care of their hot tub. If the spa has been empty in storage or has not been run for a long period of time, its elements may be degrading.
When you purchase new, you do not need to fret about any of those things. All you need to do is take care of your spa. Have a look at our basic hot tub maintenance guide to find out the best ways to keep your spa in excellent shape with our premium items.
• You Can Customize Your Hot Tub to Make it Perfect for Your Needs and Budget
By opting for an utilized hot tub, you’re sacrificing the chance to find the perfect spa for you and your household. When you purchase a hot tub new, there are a variety of choices readily available, so that you’re ensured to get the most out of your spa by discovering the very best one for you.
ThermoSpas ® Hot Tubs can be customized to match your preferences and your spending plan. You can pick the size, variety of jets, colors, functions and devices to match your taste. We provide this personalization because desire everyone to be able to delight in a hot tub that suites their needs.
• You Get Personalized Customer Service
After purchasing an utilized hot tub, you’re basically by yourself to transfer it, set it up, figure out how it works and maintain it. If it’s your first hot tub purchase, this can be a difficult and confusing procedure.
When you buy a Hot Tub, our professional agents help you every step of the method. A factory-trained service technician will visit your home to assist you discover the best location for your brand-new spa and the safest, least costly technique of setup.
If a used hot tub is looking a little less attractive to you than in the past, think about buying a new Hot Tub. Considering that numerous sell straight to the customer, you can personalize a hot tub that is built to fit your requirements and budget.

Okay, now that we have given you all the advice we can so you can rush out and buy a hot tub, we have one more thing to help you get the most benefit from it. Imagine getting all relaxed in your hot tub and then straining yourself trying to get a heavy awkward cover back onto your spa.

Washing your cares away in the warm embrace of pulsating water jets followed up with getting your blood pressure up because you get angry while putting the heavy cover back on the hot tub.

At, they have just what you need to keep those good vibrations. They have been building Custom Hot Tub Covers for thirty years. Imagine a hot tub cover as easy to use as moving a fluffy comforter onto your bed. No exasperation required. hot tub covers use air to insulate rather than foam so there is nothing to soak up moisture which is what makes all other covers heavy.

Don’t let all the good your hot tub can do for you be wasted on a heavy, outdated, obsolete cover just because that’s all your local dealer has to offer.

Spa Covers and Snow Loads

Changing your hot tub cover due to the fact that the snow squashed it?
Exactly what if there was a cover that could manage that much snow? Yes, even as much as you had.
Great news there is.
First lets take a minute and discuss why the one you require to replace didn’t make it.
The foam in the cover broke under the weight of the snow.
Was it since the metal channel that goes through the center of the cover on both sides wasn’t adequate support?
It was since the weight of the snow would have broken a 2×4 if it were aiming to bridge an eight-foot space like that.
Exactly what triggered the cover to collapse was that it was attempting to make a bridge over the spa, from one side to the other. Typically not an issue up until the cover itself gets saturated, however in this case it was the included weight of snow that just was excessive to deal with.
So, if you get a cover that does not aim to bridge the gap but supports itself by resting on the water, that would be a huge improvement.
Still, you did get a lots of snow. Would it have the ability to manage that much?
Brief answer, yes.
It appears that every couple of years, somewhere in the nation is getting snow that will be explained by their local news as “biblical percentages” which overwhelms the location, closes down schools, roads, airports and life in basic till the storm passes and individuals can remove.
Throughout those winter storm events, when the day-to-day regimen of the general public ends up being focused on surviving, how the hot tub is doing just isn’t really that important. Not surprisingly so.
When the storm passes and people start to evaluate the damages, it is not uncommon for the majority of or all of the outdoor hot tub covers to be part of the tally.
A couple of years back, I was doing house programs in Colorado. We had a program in Colorado Springs and then another in Denver with about 10 days between.
Throughout the break, I flew from Denver to be home with the household for a couple of days.
As I was leaving Denver a snowstorm was coming in and it ended up the plane I was on would be the last one permitted to take off for days.
When it was time to go back to Denver for the up coming reveal the return flight I was on removed uncertain that Denver would be all set yet by the time we got there.
It was, and we were the first plane allowed in or out since I had left. Individuals that had remained in the airport in Denver when I left were still there when I got back 10s days later on.
All of Denver had been shut down for those tens days. Denver is used to snow.
This was one of those Epic storm occasions.
Outdoor patio roofing systems had actually collapsed. Industrial buildings had roofing systems collapse. Needless to state, practically every outdoor hot tub cover had to be changed.
With one exception. As insurance representatives hurried around to assist their customers identify exactly what needed to be replaced, they found that every hot tub that did NOT have to have a brand-new cover had the same brand name of cover. Those covers were great. Not only did those covers not have to be changed however also every hot tub that was covered by one was great to. The hot tub was till running; the water was still warm even when the property owners might not get outside to shovel snow off of them. Even on the jacuzzis owned by people that were out of town throughout the storm.
The insurance coverage representatives started suggesting that their clients replace their hot tub covers with that brand. All those covers that had the ability to endure that legendary snow load were hot tub covers. No other cover was suggested.
That says something.
The spa cover had the ability to manage the storm.
When the wind blew in ahead of the storm, the SpaCap covers remained in location. They won’t blow off even in hurricane force winds. Some of the other tough foam covers did. Even covers that were too heavy for a single person to lift.
The hail won’t damage a SpaCap because it isn’t really rigid. The air inside the cover enables it to provide. No matter how huge the hail gets, it will not harm a SpaCap.
And the snow, several feet deep, didn’t damage a single one.
Prior to you simply purchase another standard hot tub cover, we recommend you check out and get the only type of cover that actually can deal with the snow.

Is there a hot tub cover that can handle a serious snow load?
Did Mother-nature dump on your hot tub cover?
Snow Crush your hot tub cover?
Searching for a hot tub cover that can deal with a lot of snow?

Should I get a Pool or a Swim Spa?

I enjoy to swim, is it better to purchase the pool or perhaps a swim spa?

One significant difference between a pool and a hot tub is the capability to use a hot tub outdoors all year long. If you live in an environment where there are cold winter seasons, this is particularly essential. You can use your hot tub 12 months out of the year, whereas with a pool you get an average of 3 months use from the year. Not to mention the space efficiency of a hot tub vs. a pool. A Swim Spa hot tub can be used like a pool, with the option to swim all year long, and it takes up much less space than a pool. In addition, a hot tub needs less chemicals, making the maintenance less costly and more Eco-friendly.

The most noteworthy drawbacks of owning a pool are:


  • minimal seasonal use
  • big area requirements
  • costly building code guidelines
  • timely upkeep
  • pricey upkeep and negative impact to home’s resale worth

In reaction to the concerns of pool ownership, Hot Tub makers designed the Swim Spa. One side offers a consistent present for the swimmer to swim against, getting an intense exercise, and the opposite of the Swim Spa permits the ultimate hot tub experience. The additional present added in the swim spa offers an included challenge to the swimmer, helping them burn more calories and become fitter and stronger. After the exercise, the swimmer can speed recovery by soaking on the hot tub side and letting the therapy jets give them a complete body massage. The Swim Spa features the alternative to include exercise bands to work out your entire body.

Fitness and swimming is not the only use for a spa fitness instructor, since this hot tub seats more individuals it is a fantastic source of home entertainment for family and friends. A Swim Spa is likewise an excellent method to teach your children the best ways to swim in a safe, regulated environment.

The Swim Spa is perfect for many years round use for fitness, leisure and entertainment!

At, they have simply what you have to keep those advantages going. They have actually been building Custom Swim Spa Covers for thirty years. Envision a Swim Spa Cover as easy to use as moving a fluffy comforter onto your bed. No exasperation needed. Swim Spa Covers use air to insulate rather than foam so there is nothing to absorb moisture which is exactly what makes all other covers heavy.

Do not let all the excellent your Swim Spa can do for you be wasted on a heavy, outdated, obsolete cover just because that’s all your local dealer needs to use. Order your own customizeded Swim Spa Cover and alter your life for the better.